Analisis Risiko K3 Pekerja Alat Container Crane Menggunakan Metode HIRARC Di PT. Pelindo Terminal Petikemas New Makassar

Nur Fitria Chaerani; Nurgahayu; Nasruddin Syam

doi:10.33096/woph.v6i1.2117

Authors

Nur Fitria Chaerani Universitas Muslim Indonesia
Nurgahayu Universitas Muslim Indonesia
Nasruddin Syam Universitas Muslim Indonesia

DOI:

https://doi.org/10.33096/woph.v6i1.2117

Keywords:

HIRARC, Risk analysis, Container crane worker

Abstract

Every workplace has a risk of workplace accidents. In general, workplace accidents are caused by two factors, namely human actions that do not meet work safety standards and environmental conditions that do not meet safety standards. Accident prevention efforts can be carried out by identifying potential risks. The general objective of this study is to conduct an analysis of Occupational Health and Safety (K3) risks using the Hazard Identification, Risk Assessment, and Risk Control (HIRARC) method on Container Crane Workers at PT Pelindo Terminal Petikemas New Makassar in 2024. The type of research conducted is quantitative research. Sampling in this study used total sampling with the same number of samples as a sample of 30 respondents. Hazard identification is carried out by conducting interviews and observations of container crane workers. In contrast, risk assessment is carried out by distributing questionnaires assessing the level of possibility and severity of the risk of each potential hazard. After knowing the risk index, risk control is then determined. Based on the research results, 10 potential sources of danger were obtained for container crane workers with a potential danger of 66.7%, risk assessment based on four work steps where work step 1 was 86.7% with a high-risk category and work step 2 was 83.3% with a low-risk category, work steps 3 and 4 were included in the low-risk category. Controls that can be carried out to reduce risk include using Personal Protective Equipment (PPE) for workers and administrative controls.

References

Muhtia, S. A., Fachrin, S. A., & Baharuddin, A. Analisis Risiko K3 Dengan Metode Hirarc Pada Pekerja Pt . Varia. Window Of Public Health Journal, 2020; 01(03): 166–176.

BPJS Ketenagakerjaan. Kecelakaan Kerja Makin Marak dalam Lima Tahun Terakhir. www.bpjsketenagakerjaan.go.id, 2023

Putri, S., & Assidiq, F. M. Analisa Bahaya dan Risiko Kecelakaan Kerja pada Pemeliharaan Alat Container Crane (CC). Riset Sains dan Teknologi Kelautan, 2022: 50-53.

Santoso, D. O., Kurniawan, M. D., & Hidayat, H. Analisa Risiko Keselamatan Dan Kesehatan Kerja Menggunakan Metode HIRARC Di PT. INHUTANI 1 UMI GRESIKHUTANI 1 UMI GRESIK. Jurnal Media Teknik Dan Sistem Industri, 2022; 6(1): 12.

Widiastuti, R., Prasetyo, P. E., & Erwinda, M. Identifikasi Bahaya Dan Penilaian Risiko Untuk Mengendalikan Risiko Bahaya Di UPT Laboratorium Terpadu Universitas Sarjanawiyata Tamansiswa. Industrial Engineering Journal Of The University Of Sarjanawiyata Tamansiswa, 2019; 3(2): 51.

Sriagustini, I., & Supriyani, T. A Analisis Bahaya Pada Pengrajin Anyaman Bambu. Faletehan Health Journal, 2021; 8(03): 223–230.

Fitrialita, A. Work Accident Risk Analysis on Height Workers Using The HIRARC Method in The MTH 27 Office Suite Project PT X in 2021. Indonesian Scholar Journal of Medical and Health Science, 2021; 1(04): 140-147.

Imran, R. A., Industri, J. T., Teknik, F., & Soedirman, U. J. Identifikasi hazard pada proses produksi billet pada area tungku peleburan dengan metode HIRARC (Studi Kasus: PT. XYZ). Jurnal Ilmiah Teknik Industri, 2020; 8(3): 153-160.

Mantiri, D. H. M., Malingkas, G. Y., & Mandagi, R. J. M. Analisis Risiko Kecelakaan Kerja Berdasarkan Aturan SMK3 Menggunakan Metode Ranking Pada Proyek Pembangunan Instalasi Rawat Inap RSUD. 2020; 10(2).

Ghika Smarandana, Ade Momon, & Jauhari Arifin. Penilaian Risiko K3 Pada Proses Pabrikasi Menggunakan Metode Hazard Identification, Risk Assessment And Risk Control (HIRARC). Jurnal INTECH Teknik Industri Universitas Serang Raya, 2021; 7(1): 56–62.

Mauliyani, H., Romdhona, N., Andriyani, A., & Fauziah, M. Identifikasi Risiko Keselamatan Kerja Metode (HIRARC) Pada Tahap Pembuatan Tangki Di PT. Gemala Saranaupaya. Environmental Occupational Health and Safety Journal, 2022; 2(2): 163-174.

Wardani, R. Penerapan Manajemen Risiko Keselamatan Dan Kesehatan Kerja Pada Kegiatan Bongkar Muat Di Pt. Pelabuhan Indonesia Iv (Persero) Cabang Makassar= The Implementation Of Occupational Health And Safety Risk Management Loading And Unloading In Pt. Pelabuhan Indonesia Iv (Persero), Makassar Branch (Doctoral Dissertation, Universitas Hasanuddin), 2022.

Smarandana, G., Momon, A., & Arifin, J. Penilaian Risiko K3 pada Proses Pabrikasi Menggunakan Metode Hazard Identification, Risk Assessment and Risk Control (HIRARC). Jurnal INTECH Teknik Industri Universitas Serang Raya, 2021; 7(1): 56-62.

Purwanto, E. B. I., Widada, D., & Tambunan, W. Analisis Risiko K3 pada Bongkar Muat di Pelabuhan dengan Metode HAZOP (Hazard Analysis And Operability Study)(Studi Kasus: PT. XYZ). Journal Of Industrial And Manufacture Engineering, 2023; 7(2): 180-191.

Santa Yoviana Putri, Dan Fuad Mahfud Assidiq S.T., M. T. Analisa Bahaya Dan Risiko Kecelakaan Kerja Pada Pemeliharaan Alat Container Crane (CC). Seminar Sains Dan Teknologi Kelautan, 5(November), 2021: 45–49.

Situngkir, D., Rusdy, M. D. R., Ayu, I. M., & Nitami, M. Sosialisasi Keselamatan Dan Kesehatan Kerja (K3) Sebagai Upaya Antisipasi Kecelakaan Kerja Dan Penyakit Akibat Kerja (Pak). JPKM : Jurnal Pengabdian Kesehatan Masyarakat, 2021; 2(1): 64–72.